How do you actually feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't precisely brain surgery, however it does need strong plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging job. If the old tub is easily easily accessible, the job can relocate immediately; if you need to open up a wall to remove the old tub and also place the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the work and fit trying it. Rather than hiring a professional to take control of a halfway-completed job, it is far better to take into consideration utilizing one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to alter the plan of your previous supply of water pipelines.
Your devices and product list ought to consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing taps can be rather troublesome because of the limited gain access to that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Secure the tap in position with the maker supplied backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet ports. The former kind needs to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Using the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub until the level reads degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water and inspect all joints and also new pipework for leaks and tighten them if needed. Load the bathtub and likewise examine the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also sealing around the bathtub ought to wait till the bath tub has been used a minimum of when as this will certainly resolve it into its final setting.
Planning for the Setup
To start with, the sustaining framework provided with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must now prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, causing complications with dampness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very serious about A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed reading our blog entry. Loved our review? Please share it. Let somebody else discover it. I appreciate reading our article about How to Install a Bathtub.
Suggested Site